• 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve

23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve

No.23421183
Ingersoll Rand inlet valve 23421183 for R90-110I/N screw compressors. 20 kg unit, also listed as Hoerbiger 1257076. In stock at USD 750.
$750.00
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve
  • 23421183 Ingersoll Rand Screw Air Compressor Genuine Parts Inlet Valve

Description

Cross reference Hoerbiger 1257076
Weight 20 kg
Dimensions 42 × 40 × 36 cm
Fits Ingersoll Rand R90-110I / R90-110N
Lead time In stock

What it does

The inlet valve is the throttle of the machine. It decides how much air enters the airend, and the controller strokes it to hold a pressure band rather than running flat out. It closes on shutdown so the airend starts unloaded.

On an R90-110 machine this is a substantial casting — 20 kg, roughly 42 × 40 × 36 cm — and the seat rather than the body is what wears. Seat wear shows up as a pressure shortfall, not as a leak, which is why it often goes unnoticed until the machine stops meeting demand.

Signs it needs replacing

  • Rated pressure is no longer reached, or takes much longer to build
  • Rapid load and unload cycling against steady demand
  • The machine restarts loaded, and the starter sounds strained
  • Air audible at the shaft seal with the machine unloaded
  • A polished band or step worn into the seat, visible on inspection

Replacement interval

Replace on condition. Seat wear tracks cycle count rather than hours, so a machine on variable demand wears it faster than one running flat out. Inspect at 8,000 hours.

How to replace

  • Isolate and lock off, vent the sump and the control air. Support the valve before undoing the flange — at 20 kg it will drop.
  • Record the control port layout. The lines sit close together and two crossed gives a valve that strokes the wrong way.
  • Fit a new gasket and clean both faces. Over a seat this wide a distorted face leaks in a way that mimics seat wear.
  • Check the servo cylinder bore and the shaft for scoring while the valve is out.
  • Cycle load and unload, confirm full closure on stop, then release the machine.

Cross reference

This valve is also supplied under the Hoerbiger number 1257076. Same unit, two catalogues: machines documented against a Hoerbiger service list show 1257076, Ingersoll Rand parts books show 23421183.

Order by whichever number appears in your manual. Both are stocked here.

Ordering notes

Fits Ingersoll Rand R90-110I and R90-110N. Send the machine model and serial before ordering, since the I and N variants differ in build and the port arrangement follows the variant.

Weight 20 kg, packed 42 × 40 × 36 cm. In stock.

Can I get a better price?

Prices indicated on this website are guide prices and are subject to manufacturer's policies and
Purchase quantities and other factors may change, subject to the actual communication sent to the offer shall prevail.

Couldn't find the part I wanted?

This website will keep adding new products, but there's a limit to the number of products that can be uploaded because of time restrictions and other issues. If you can't find the product you need, please contact us.

How soon I can get a price quote?

You can get a quick price quote within a few minutes if you are on live chat with one of our sales representatives and a standard price quote takes just 30-45 minutes and you will have an official price quote in your inbox.

Does it include shipping?

The products sold in our store include shipping within mainland China, but export shipping costs are extra. Our store works with many international delivery companies, including DHL.
You can enjoy low discount prices when you use FedEx. We also work with major freight forwarding companies. They can transport your goods by sea or rail.