• 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41

1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41

No.1616747281
Atlas Copco oil-free airend 1616747281, replaces 1616679281. Complete compression unit for oil-free screw compressors. USD 24,300, Belgium, 2-4 weeks.
$24250.00
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41
  • 1616747281 Atlas Copco Air Compressor Genuine Parts Airend O.F.S. I-41

Description

Part No 1616747281
Supersedes 1616679281
Brand Atlas Copco
Origin Belgium
Dimensions 57 × 44 × 43 cm
HS Code 8414909090
Fits Atlas Copco oil-free compressors
Lead time 2-4 weeks

What it does

The airend is the compression unit itself: the rotor pair, the housing and the bearings. Everything else on the machine supports it. On an oil-free compressor there is no oil film between the rotors to carry heat away or seal clearances, so the rotor coating and the bearing condition carry that load directly.

1616747281 replaces 1616679281 and is supplied as a complete exchange airend.

Signs it needs replacing

  • Delivery volume falls at the same speed and pressure set point
  • Discharge temperature climbs with the cooler working correctly
  • Rotor contact noise, or a metallic note at start and stop
  • Vibration or axial play at the coupling end
  • Air quality results drift out of the class the machine was bought for

On an oil-free machine the last item matters most. A worn airend can still deliver pressure while the air no longer meets specification, and that usually surfaces as a failed customer audit rather than a fault code.

Replacement interval

Airends are not on a fixed replacement schedule. They are replaced when wear shows in delivery, temperature or air quality. Bearing life follows the load profile and starting frequency: machines that cycle hard wear the bearings before the rotors.

Compare delivery volume against input power over time. A slow rise in specific power is the earliest signal, and it appears long before an operator notices anything.

How to replace

  • Isolate, lock off and confirm the discharge line is at zero pressure.
  • Record coupling alignment and shim positions before removal. Refitting without the original alignment is the most common cause of a repeat failure.
  • Support the airend on its mounting points during removal. Do not let it hang on the pipework.
  • Replace the coupling element and check motor shaft runout while the airend is out.
  • After refitting, run a full load test and an air quality test before returning the machine to service.

Genuine vs alternative

This is a genuine Atlas Copco exchange airend. Rebuilds and third-party units exist at this size, and they are a different commercial decision rather than a cheaper version of the same thing: a rebuild ties the machine to the rebuilder's turnaround and warranty, while an exchange unit restores the original performance specification on delivery.

Genuine Atlas Copco: USD 24,300

Ordering notes

Send the machine nameplate before ordering. Airend specification follows the machine build, and the nameplate is what confirms the correct unit.

Dimensions 57 × 44 × 43 cm. Lead time 2-4 weeks.

Can I get a better price?

Prices indicated on this website are guide prices and are subject to manufacturer's policies and
Purchase quantities and other factors may change, subject to the actual communication sent to the offer shall prevail.

Couldn't find the part I wanted?

This website will keep adding new products, but there's a limit to the number of products that can be uploaded because of time restrictions and other issues. If you can't find the product you need, please contact us.

How soon I can get a price quote?

You can get a quick price quote within a few minutes if you are on live chat with one of our sales representatives and a standard price quote takes just 30-45 minutes and you will have an official price quote in your inbox.

Does it include shipping?

The products sold in our store include shipping within mainland China, but export shipping costs are extra. Our store works with many international delivery companies, including DHL.
You can enjoy low discount prices when you use FedEx. We also work with major freight forwarding companies. They can transport your goods by sea or rail.